How do I use ceratec?
What is Cera Tec and how do I apply it?
- direct addition to the motor or transmission oil (cold or warm)
- ideally, pour in together with fresh oil when changing the oil.
- 300 ml is sufficient for up to 5 liters of motor oil.
- the optimal dosage is about 6 % of the total oil fill quantity.
What does Liqui Moly ceratec do?
High-tech ceramic wear protection. Reduces friction and wear through ceramic compounds offering high chemical and thermal resistance. Prevents direct metal-to-metal contact, thus increasing the assembly service life. Reduces fuel consumption in gasoline and diesel engines thanks to the low-friction effect.
How do you use Liqui Moly Oil Additive?
Use. The dosage of Oil Additive should be 3-5% of the oil filling quantity. Oil Additive can be used at any time, even between oil changes. However, care should be taken that the maximum oil filling quantity including additive is not exceeded.
What is MoS2 additive?
MoS2 Anti-Friction Engine Treatment ensures immediate friction and wear reduction, adds an extremely protective and pressure-resistant boundary layer with low friction and lubricates during cold starts to prevent damage from lack of oil. Contributes to lower fuel consumption, longer engine life and less noise.
Can you use Ceratec and MoS2?
No, you can not, you can switch between Ceratec and Mos2 but never mix them, no together.
Can Ceratec be used in diesel engine?
Use in 4-stroke gasoline and diesel engines, with or without turbochargers. Miscible with most commercially available motor oils. Safe with catalytic converters and particulate filters (GPF/DPF) as well as for belt-in-oil systems.
Can you use ceratec and MoS2?
Does Liqui Moly MoS2 work?
It has good cold-start behavior, as well as improved wear characteristics for modern engines. LIQUI MOLY MoS2 is also recommended for older Porsches with air-cooled engines. The extra additives are very effective at reducing wear for high-heat situations, another difficulty for oil manufacturers.
What is the name for MoS2?
Molybdenum sulfide
Molybdenum disulfide [molybdenum(IV) sulfide, MoS2] is an inorganic compound that exists in nature in the mineral molybdenite….Molybdenum disulfide. fast facts.
| CAS Reg. No. | 1317-33-5 |
|---|---|
| SciFinder nomenclature | Molybdenum sulfide (MoS2) |
| Empirical formula | MoS2 |
| Molar mass | 160.07 g/mol |
Is ceratec better than MoS2?
Liqui Moly Cera Tec is similar to MoS2 in the sense that it is also a friction reducer. What differs however is the more advanced formula used to create the low surface friction. Cera Tec works similar to Oil Additive but utilizes tiny ceramic particles in place of MoS2 that is claimed to be stronger.
Can I add ceratec after oil change?
Ceratec is meant to be put in the engine when the engine only has been changed. Once added you would leave it in the oil until your normal interval for changing the oil.
Can I use ceratec on every oil change?
Liqui Moly recommends adding it to fresh oil during a oil change or add to existing oil when you have at least 5,000km (3,100 miles) left before an oil change. This gives the product sufficient time to coat all areas — once coated last for 50000km (31,000 miles) so it is not needed every oil change.
How to add ceratec to the oil?
Put 3.7 Liters of Oil, then add 300 ml of Ceratec. Check the oil gauge for level of oil. If full, then stop, otherwise add the required amount of oil and check level till it is full.
What is the movie Instructions Not included about?
Instructions Not Included (Spanish title: No se aceptan devoluciones, literally Refunds not accepted) is a 2013 Mexican comedy-drama film co-written, directed by, and starring Eugenio Derbez. The plot follows a Mexican playboy who is suddenly saddled with a love child at his doorstep, and sets off to Los Angeles to find the mother.
How do I start my next project with ceratec?
Visit our professional website and start your next project. The entire team of Ceratec Surfaces wishes you a happy holiday seasons. Combine the wide selection of pattern tiles to create your own unique composition.
How to create your own holiday project with ceratec surfaces?
Visit our professional website and start your next project. The entire team of Ceratec Surfaces wishes you a happy holiday seasons. Combine the wide selection of pattern tiles to create your own unique composition. Explore the two sides of Metallica with its vibrant wall tiles and lightly metallic floor tiles.